[Free] 2018(Jan) EnsurePass Testinsides Juniper JN0-533 Dumps with VCE and PDF 41-50

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-533
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-533.html

FWV, Specialist (JNCIS-FWV)

Question No: 41

A routing table contains an IBGP route for 192.168.0.0/24, a RIP route for 192.168.0.0/23, an OSPF route for 192.168.0.0/22, and a static route for 192.168.0.0/16.

When the router receives traffic destined for 192.168.0.1, which route will the router use?

  1. the IBGP route

  2. the OSPF route

  3. the RIP route

  4. the static route

Answer: A

Question No: 42

– Exhibit –

NSPROD1(M)-gt; get nsrp ha-link total_ha_port = 2

probe on ha-link is disabled

unused channel: ethernet8 (ifnum: 11) maC.0010db1d1e8b statE.down unused channel: ethernet7 (ifnum: 10) maC.0010db1d1e8a statE.down ha control link not available

ha data link not available

ha secondary path link not available

– Exhibit –

Referring to the exhibit, both clustered devices are in a master state. What is the cause of this situation?

  1. The cluster is not configured for NSRP.

  2. The cluster is in the process of failing over from the primary node to the secondary node.

  3. Probes on the HA links have been disabled, causing the HA links to go down.

  4. The control and the data link is down.

Answer: D

Question No: 43

What is the function of NAT?

  1. It performs Layer 3 routing.

  2. It evaluates and redirects matching traffic into secure tunnels.

  3. It provides translation between IP addresses.

  4. It performs Layer 2 switching.

Answer: B

Question No: 44

A ScreenOS device evaluates five primary elements when performing a security policy check on a new session.Which five elements are evaluated?

  1. source IP address, destination IP address, source route, source port, and destination port

  2. source IP address, destination IP address, source port, destination port, and protocol

  3. source IP address, destination IP address, source port, destination port, and payload

  4. destination IP address, source port, destination port, protocol, and payload

Answer: B

Question No: 45

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Which two statements are true about the default route configuration based on the output shown in the exhibit? (Choose two.)

  1. A default route is configured in the trust-vr with a next-hop IP address of 1.1.1.1.

  2. A default route is configured in the trust-vr with a next hop of ethernet3/1.

  3. A default route is configured in the trust-vr with a next hop of the untrust-vr.

  4. A default route is configured in the untrust-vr with a next-hop IP address of 1.1.1.1.

Answer: C,D

Question No: 46

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Referring to the exhibit, what does the log show?

  1. The device is using VIP.

  2. The device is using DIP ID 4.

  3. The device is using source NAT.

  4. The device is using destination NAT.

Answer: C

Question No: 47

You have enabled BGP on your ScreenOS device and configured a single EBGP peer. The CLI shows that the BGP connection is transitioning between the CONNECT and ACTIVE states, but never reaching the ESTABLISHED state.

What are three reasons for this behavior? (Choose three.)

  1. The peer is blocking traffic destined for TCP port 179.

  2. The peer address is not configured correctly.

  3. The enable statement has not been configured for the peer.

  4. The peer AS number is not configured correctly.

  5. BGP has not been enabled on the virtual router.

Answer: A,B,D

Question No: 48

You are using debug to determine which policy is used for Web traffic from host 10.20.1.5 to server 10.240.1.100.Which flow filter will only capture traffic related to this scenario?

A. id:0 src ip 10.20.1.5 dst ip 10.240.1.100

id:1 src port 80

B. id:0 src ip 10.240.1.100 dst ip 10.20.1.5 id:1 src port 80

C. id:0 src ip 10.240.1.100 dst ip 10.20.1.5 dst port 80

D. id:0 src ip 10.20.1.5 dst ip 10.240.1.100 dst port 80

Answer: D

Question No: 49

On a ScreenOS device, which three processes does the task CPU handle? (Choose three.)

  1. policy evaluation

  2. traffic logging

  3. session table clean-up

  4. management services

  5. broadcast packet processing

Answer: B,C,D

Question No: 50

Which two configuration elements are synchronized between the members of an NSRP cluster? (Choose two.)

  1. interface IP addresses

  2. hostname

  3. track IP configuration

  4. static routes

Answer: A,D

100% Ensurepass Free Download!
Download Free Demo:JN0-533 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-533 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No