[Free] 2018(Jan) EnsurePass Passguide Juniper JN0-692 Dumps with VCE and PDF 41-50

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-692
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-692.html

Service Provider Routing and Switching Support, Professional

Question No: 41 – (Topic 1)

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

You have created a new IS-IS adjacency between identical routers over two STM-4 circuits. After enabling no-keepalives on the interfaces, they come up and you are able to ping between the routers. However, the IS-IS adjacency still will not establish.

Which step will determine the cause of the problem?

  1. Disable no-keepalives from the interfaces and issue a show isis adjacency command.

  2. Enable family iso on all the SONET interfaces, commit, and test the circuits.

  3. Disable cisco-hdlc encapsulation, enable ppp encapsulation, commit, and test the circuits.

  4. Disable no-keepalives from the interfaces and issue a show interfaces extensive command for each of the SONET interfaces.

Answer: D

Question No: 42 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Based on the output in the exhibit, which statement is correct?

  1. R4 has been configured with an IS-IS export policy and is announcing external routing information.

  2. R3 and R4 have an adjacency at both level 1 and level 2.

  3. R3 has been configured so that it is not used for transit traffic.

  4. R3 and R4 are both attached to other IS-IS areas.

Answer: C

Question No: 43 – (Topic 1)

You have applied a customized EXP rewrite rule on router R1 on the egress of the interface connecting to router R2. You want to verify if it is working properly. Which two methods would you use to accomplish this task? (Choose two.)

  1. Apply a rewrite rule on the ingress of R2 for packets coming in from R1 and count those packets for the new EXP values with a firewall filter as they leave R2.

  2. Use the traceroute utility.

  3. Use an output filter on R1 that matches and counts on various EXP values on packets going to R2.

  4. Use an input firewall filter on R2 that matches and counts on various EXP values on packets coming from R1.

Answer: C,D

Question No: 44 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

CE1, CE2, and CE3 are part of a single VPLS VPN. R1, R2, and R3 are PEs in the provider network, and have just been powered on. The VPLS domain has converged, and frames have passed between all CEs in the last minute. An Ethernet frame has just arrived at R3 from CE3. It has a source MAC address of CE3 and a destination MAC address of CE1.What does R3 do with the Ethernet frame?

  1. Drops the packet as the destination MAC address is not for R3.

  2. Drops the packet as the destination MAC address is not in R3#39;s MAC table.

  3. Forwards the packet to R1 only.

  4. Forwards the packet to R1 and R2.

Answer: C

Question No: 45 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

You work for ISP A, as shown in the exhibit, and must configure R1 to use load balancing across both available links to ISP B#39;s network. Which command do you use to finish the configuration?

  1. set protocols bgp group isp-b multipath

  2. set routing-options forwarding-table export per-packet

  3. set protocols bgp group isp-b multihop

  4. set routing-options forwarding-table load-balance

Answer: A

Question No: 46 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

The exhibit contains a BGP topology. R1 and R2 are peering using IBGP. R2 and R3 are peering with EBGP. R1 is not installing any routes from R3 due to next-hop resolution issues. Which two configurations will resolve this issue? (Choose two.)

  1. Use a policy to advertise the loopback on R2 into the IGP.

  2. Advertise the R2-R3 subnet into the IGP.

  3. Configure advertise-inactive on the IBGP peering session on R2.

  4. Configure next-hop self on the IBGP peering session on R2.

Answer: B,D

Question No: 47 – (Topic 1)

An OSPF neighbor between routers R1 and R2 is stuck in loading state on R2. What are two causes? (Choose two.)

  1. OSPF is not enabled on the interfaces.

  2. A firewall filter is blocking OSPF hellos on both sides.

  3. The R1 router has received a corrupted link-state request packet.

  4. The interface MTU is mismatched between the routers.

Answer: C,D

Question No: 48 – (Topic 1)

What are three Junos automation scripts? (Choose three.)

  1. op scripts

  2. pulse scripts

  3. commit scripts

  4. event scripts

  5. action scripts

Answer: A,C,D

Question No: 49 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

You are the administrator of AS 65000. In the exhibit, there are four links between your network (AS 65000) and your upstream provider (AS 65001).

You have an export policy on all of your routers to advertise your routes such that: Router A: MED 100, AS Path (65000), Origin 1

Router B: MED 100, AS Path (65000 65000), Origin 0

Router C: MED 50, AS Path (65000 65000), Origin 1

Router D: MED 50, AS Path (65000), Origin 0

Through which link will traffic from the Web server enter your network (AS 65000)?

  1. Router A

  2. Router B

  3. Router C

  4. Router D

Answer: D

Question No: 50 – (Topic 1)

In an interdomain multicast deployment scenario, an RP1 is in AS1 and an RP2 is in AS2. MSDP is configured between RP1 and RP2.In which routing table on RP1 are source- active messages (SAs) received from RP2 by default?

  1. inet.0

  2. inet.2

  3. inet.1

  4. inet.4

Answer: D

100% Ensurepass Free Download!
Download Free Demo:JN0-692 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-692 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No